Detailed Tutorial on How to Make a Bling Beaded Slave Bracelet with Glass Beads and Seed Beads

Slave bracelet is a favored piece of jewelry among people. Today, you can see a bling beaded slave bracelet. The design idea of this beaded slave bracelet comes from this crystal beaded bracelet shared by Monica Benz. Now, let's see the detailed tutorial on how to make the beaded slave bracelet with glass beads and seed beads.

Materials and tools needed in DIY the bling beaded slave bracelet:

14x7mm Red Glass Back Rhinestone Cabochon
8x6mm Clear Abacus Glass Beads
4mm Clear Bicone Glass Beads
2mm Clear Round Seed Beads
Red 2-Hole Seed Beads
Golden Pad Ring Base
Slide Lock Clasp
0.2mm White Fishing Wire
Stainless-Steel Scissor
Glue Gun

Instructions on how to make the bling beaded slave bracelet:

Step 1: Make the first part of the bling beaded slave bracelet

1st, cut about 500cm 0.2mm white fishing wire. Then, add 12 2mm clear round seed beads and 12 red 2-hole seed beads to the wire (as shown in the picture);
2nd, make some knots with the two wires and cut off one wire (as shown in the picture);
3rd, add 2 2mm clear round seed beads. Then, cross the wire through the other hole of the adjacent red 2-hole seed bead (as shown in the picture);
4th, refer to the above steps to add more 2mm round seed beads (as shown in the picture);
5th, add a red 2-hole seed bead. Then, cross the wire through the two adjacent seed beads (as shown in the picture);
6th, refer to the above steps to add more red 2-hole seed beads (as shown in the picture).

Step 2: Make the second part of the bling beaded slave bracelet

1st, cross the wire through the other hole of one red 2-hole seed bead. Then, add a 2mm clear round seed bead and cross the wire through the other hole of the adjacent red 2-hole seed bead. Repeat this step to add more round seed beads (as shown in the picture);
2nd, add a 14x7mm red glass back rhinestone cabochon to the middle and cross the wire through the beads and tighten (as shown in the picture);
3rd, add a 4mm clear bicone glass bead and 4 2mm round seed beads (as shown in the picture);
4th, cross the wire through the 4th seed bead (count from right to left). Then, add another 4mm clear bicone glass bead (as shown in the picture);
5th, cross the wire through the two round seed beads (as shown in the picture);
6th, repeat the above steps to make more such patterns. Then, cut off the excess wires (as shown in the picture).

Step 3: Make the third part of the bling beaded slave bracelet

1st, cut another piece of wire and add about 18 2mm clear round seed beads to it (as shown in the picture);
2nd, make some knots with the two sides of the wire and cut off one wire (as shown in the picture);
3rd, add 3 clear round seed beads (as shown in the picture);
4th, cross the wire through the 3 seed beads (as shown in the picture);

5th, add a 4mm clear bicone glass bead and 4 2mm clear round seed beads (as shown in the picture);
6th, cross the wire through the 4th seed bead (count from right to left). Then, add a 4mm clear bicone glass bead (as shown in the picture);
7th, refer to the above steps to make two more such bead patterns. Then, cross the wire through the beads (as shown in the picture);
8th, add a 4mm clear bicone glass bead and 4 2mm clear round seed beads (as shown in the picture);
9th, cross the wire through the leftmost seed bead of the 4 seed beads added just now. Then, refer to the above steps to make two more such bead patterns. Add a 4mm clear bicone glass bead (as shown in the picture);
10th, cross the wire through the seed bead (as shown in the picture).

Step 4: Make the fourth part of the bling beaded slave bracelet

1st, refer to the above steps to make more such bead patterns (as shown in the picture);
2nd, add a 2mm clear round seed bead, an 8x6mm clear abacus glass bead and a clear round seed bead in sequence (as shown in the picture);
3rd, cross the wire through the 8x6mm clear abacus glass bead and the two clear round seed beads (as shown in the picture).

Step 5: Make the fifth part of the bling beaded slave bracelet

1st, cross the wire through the seed beads and glass beads. Then, add a 4mm clear bicone glass bead and 4 2mm clear round seed beads. Then, cross the wire through the leftmost seed bead of the 4 seed beads added just now (as shown in the picture);
2nd, add a 2mm clear round seed bead, an 8x6mm clear abacus glass bead and a 2mm clear round seed bead in sequence. Then, cross the wire through glass bead and the seed beads (as shown in the picture);
3rd, add a 4mm clear bicone glass bead and 4 2mm clear round seed beads. Then, make a hoop with the 4 round seed beads. Repeat this step to make another such bead patterns. Add a 4mm clear bicone glass bead and cross the wire through the round seed bead (as shown in the picture);
4th, cross the wire through the beads. Then, add a 4mm clear bicone glass bead and 4 2mm clear round seed beads and make a hoop with the four round seed beads. Repeat this step to make another such bead pattern. Add a 4mm clear bicone glass bead and cross the wire through the seed bead (as shown in the picture);
5th, refer to the above steps to make more such bead patterns. Then, refer to the above steps to make a corresponding circular part on the right end. Cross the wire through the glass beads and seed beads (as shown in the picture).

Step 6: Make the sixth part of the bling beaded slave bracelet

1st, refer to the above steps to make another square bead pattern in the middle (as shown in the picture);
2nd, refer to the above steps to make 6 more such square bead patterns. Then, add a 4mm clear bicone glass bead and 4 2mm round seed beads. Make a hoop with the 4 round seed beads and add another 4mm clear bicone glass bead (as shown in the picture);
3rd, refer to the above steps to make another square bead pattern. Then, add the bead flower and cross the wire through the beads (as shown in the picture).

Step 7: Make the rest part of the bling beaded slave bracelet

1st, add some round seed beads and 4 clear bicone glass beads to the wire. Then, cross the wire through the round seed bead (as shown in the picture);
2nd, cross the wire through the beads. Then, refer to the above step to add another bead strand (as shown in the picture);
3rd, refer to the above steps to add two corresponding bead strands on the other side (as shown in the picture);

4th, refer to the above steps to add two short beaded strands (as shown in the picture);
5th, use glue gun to attach a golden pad ring base on the back surface of the bead flower. Then, add a slide lock clasp (as shown in the picture).

Here is the final look of the bling beaded slave bracelet.

Do you like this bling beaded slave bracelet? The perfect combination of glass beads and seed beads make the beaded slave bracelet attractive. Maybe the instructions are a little complicated, but the result is good. Try to make one if you like this beaded slave bracelet.