Instructions on How to Make a Purple and White Pearl Bow Hair Clip with Dangle

Supplies in making the purple and white pearl bow hair clip with dangle:

6mm Light Purple Pearl Beads
4mm White Pearl Beads
3mm Gold Bead Spacers
Assorted Shape Purple Pearl Beads
10mm Yellow Pearl Beads
1cm Purple Ribbon
Silver Bead Cap
Gold Jump Rings
Gold Headpins
Gold Twisted Chains
Hair Clip
0.38mm Tiger Wire
Round Nose Plier
Long Nose Plier
Scissors
Glue Gun

How to make the purple and white pearl bow hair chip with dangle?

Step 1: Stitch basic patterns with gold bead spacers

1st, snip off a piece of 0.38mm tiger wire (about 45cm), thread it through 4 gold bead spacers;
2nd, thread one end of the wire through the first bead spacer, then thread each wire through a bead spacer and finally cross them with another bead spacer and tighten;
3rd, repeat the procedure and make 2 more patterns.

Step 2: Stitch a half pearl bow pattern

1st, snip off another piece of tiger wire (about 60cm), thread it through the 2 gold spacers as shown in the picture;
2nd, cross the wire ends through a 4mm white pearl bead, then thread each end through a 4mm white pearl, and then cross them through another white pearl bead again;
3rd, bead another pattern, then thread each wire through a 4mm white pearl, and then cross them through a 6mm light purple pearl bead and tighten;
4th, thread each wire end through a 4mm white pearl, then cross them through a 6x10mm pearl bead and tighten;
5th, add a 4mm white pearl to each wire, then cross the wires through a 18x6mm purple pearl bead and tighten;

6th, stitch a symmetrical pattern with the same procedures;
7th, thread the wire along several bead and trim off it.

Step 3: Sew up the 2 components

1st, snip off a short tiger wire (about 25cm), then thread it through the 2 white pearl beads on the fringes;
2nd, cross the ends through a gold bead spacer, then thread the wire through the next pearl bead on each fringe, and cross them cross another gold spacer;
3rd, repeat this procedure and stitch along till the end, and trim off the extra wires.

Step 4: Make the other half of the bow

Repeat all the procedures in step 2 and step 3 to make the other half of the bow.

Step5: Make a smaller bow

1st, snip off a piece of 0.38mm tiger wire (about 50cm), then thread it through 2 gold spacers as pictured;
2nd, cross both wires through a 4mm white pearl, then thread each wire through a 4mm white pearl bead, and then cross the wires through a 6mm light purple pearl bead and tighten;
3rd, thread each wire through a white pearl, then cross them through a 10x6mm pearl bead and tighten;
4th, thread each wire through a white pearl , then cross them through a 18x10mm purple pearl bead and tighten;
5th, stitch a symmetrical pattern with the same procedures;
6th, thread the wire along several bead and trim off it;
7th, snip off a short wire and sew up the 2 components; 8th, repeat above procedures and finish the other half of the bow.

Step 6: Finish the pearl beaded bow

1st, thread the wires across the gold bead spacer on the top;
2nd, thread the wires along several bead and finally trim off them.

Step 7: Add yellow pearl dangle

1st, thread a gold headpin through a 10mm yellow pearl bead and a silver bead cap;
2nd, twist a loop at the end of the headpin, then attach a small piece of gold twisted chain;
3rd, attach the yellow pearl dangle to the pearl bow with a gold jump ring.

Step 8: Finish the pearl bow hair clip

1st, cut a piece of 1.2cm purple ribbon, and stick it to the surface of the bare hair clip and cut off the extra ribbon;
2nd, stick the pearl beaded bow on the hair clip and let it dry.

Look! This is the final piece of this white and purple pearl bow hair clip!

I was surprised by its beauty after finishing my purple and white pearl bow hair clip with dangle! It was so lovely and charming that I couldn't help focusing my sight on it! Of course I wore it on my hair after that. This is a great design as for hair clip for girls, and if you've already known how to make a bow hair clip, then give it a try!!