Fabulously Easy handmade Jewelry for Girls - Making String Bracelet in 3 Steps
Summary: A 3-step handmade jewelry tutorial that instruct you how to make string bracelets; if you’re just obsessed with friendship bracelet, you’ll love this pattern here!
Nylon Bead Cord, DIY Bracelet Making Cord, DeepPink, about 1mm in diameter, 35m/roll(NS018-19)
Unit: 25 Rolls Weight: 762(g)
US $19.05 / 25 Rolls
Iron Bead Spacers, Golden Color, 4mm in diameter, hole: 1.5mm(E148Y-G)
Unit: 10000 pcs Weight: 1212(g)
US $6.10 / 10000 pcs
Tiger Tail, Silver-Gray, 0.5mm in diameter, about 35m/roll(L0.5MM01)
Unit: 10 rolls Weight: 467(g)
US $7.62 / 10 rolls
Iron Scissors, Covered By Plastic, Black, 120x65x8mm(TOOL-D005-5)
Unit: 30 pcs Weight: 690(g)
US $32.01 / 30 pcs
Brass Crimp Beads, Nickel Free, Tube, Golden, about 1.5mm in diameter, hole: 1mm(E001-NFG)
Unit: 30000 pcs Weight: 189(g)
US $10.06 / 30000 pcs
Brass Lobster Claw Clasps, Nickel Free, Golden, about 12mm long, 7mm wide, 3mm thick, hole: 1mm(KK-902-G-NF)
Unit: 200 pcs Weight: 93(g)
US $6.10 / 200 pcs
Jewelry Pliers, Chain-Nose(Flat Nose), Ferronickel, Nickel Color, Black/Red, 12.5cm long(P025Y-1)
Unit: 1 Plier Weight: 82(g)
US $0.88 / 1 Plier
Friendship bracelets, or string bracelets, have long been associated with campus, friendship and young girls. And nowadays, they are back bigger! Here, we’ll share you a handmade bracelet out of string and spacer bead strand. Only 3 steps and less than half an hour are required!
Supplies needed for making the string bracelet:
Golden Spacer Bead
Lobster Claw Clasp
0.5mm Tiger Tail Wire
1mm Nylon Thread
Flat Nose Plier
How to make the string and bead bracelet?
Step1: Make the spacer bead strand
1st, cut a 50cm long wire and attach a crimp bead at 5cm from the end;
2nd, slide the spacer bead one after one;
3rd, stop when the beads strand almost twice the length of your wrist circumference;
4th, attach another crimp bead at end to stop beads from dropping and adjusting the tightness among beads on wire.
Step2: Wrap on the string
1st, cut a length of 1mm nylon thread, measuring about 100cm;
2nd, fold it in half;
3rd, fold you beaded strand as picture shows and loop the thread around the area between first two beads. Bring one end going over the beaded strand and the other one going under;
4th, twist two ends together to turn the cord in opposite direction. Angling down to the next gap and repeat the process above;
5th, continue crossing over and filling in the gaps;
6th, remove the two crimp beads at ends and tie the two ends of tiger tail wire;
7th, secure two thread end with a tight knot. Make sure and then trim off any excess thread.
Step3: Attach the clasp
Open the jumprings and attach the clasp at end!
So, there you’ve your new string bracelet!
Making string bracelet is easy and it’s all the rage these days. Browse more handmade jewelry making tutorial and you can make the one of a kind accessory for yourself or give it away to a friend, and then wait for other’s compliments.